Varnish PP Extra 1 + 1L 2 component
Stock Status: Out of stock
Note: Only quantities are available in stock. Currently out of stock. Please request a quote.
Description
A hard, two-component build-up varnish with excellent filling properties based on alkyd resin and isocyanate. Excellent resistance to scratching, water, alcohol and household chemicals. For use as a quick drying build-up coat, as a sealer or filling coat in a one-component and two-component synthetic or polyester based varnish system or, as an isolating sealer for oily and vaporous woods such as teak and iroco. Can be used as an interior finish on any wood type i.e. cabinet doors, galley furniture, interior trim etc. Ideally suited as a maintenance coat over existing, intact, clear, two-component interior varnish systems. For exterior use, overcoating with a minimum of three coats Epifanes clear gloss varnish (one-component) or three coats Epifanes poly-urethane clear gloss (two-component) is required to provide UV protection. Mixing ratio is 1:1 by volume. Potlife after mixing 8 hours at 20°C (70°F). Temperature should be between 15°C And 27°C (60°-80°F) during application.
Thinner : All applications - Epifanes thinner for PP varnish extra.
Recoatable : After 5 hours at 18°C (65°F)
Brush wet-on-wet after 5 hours at 18°C (65°F)
Spray wet-on-wet after 2.5 hours at 18°C (65°F)
Coverage : 2 liters is sufficient for 28 m² (300 ft²)
General Specification
| INTERIOR | ||||
| Coats | First | Second | Third | More as needed |
| Thinner | Thinner for PP Varnish | Thinner for PP Varnish | Thinner for PP Varnish | Thinner for PP Varnish |
| Thinning Ratio % (brush/roller) | 43961 | 5 | 0-5 | 0-5 |
| Abrasive grit | n/a | 280 Dry | 360 Wet or Dry | 360 Wet or Dry |
| Sanding | n/a | After 24 hours | After 24 hours | After 24 hours |
| Recoat Time 65F./18C | Within 24 hours, no sanding required | Within 24 hours, no sanding required | Within 24 hours, no sanding required | Within 24 hours, no sanding required |
| Notes | Can be recoated after 5 hours | |||
| Exterior | ||||
| Coats | First | Second | Third | Fourth |
| Thinner | Thinner for PP Varnish | Thinner for PP Varnish | Thinner for PP Varnish | Thinner for PP Varnish |
| Thinning Ratio % (brush/roller) | 43961 | 5 | 0-5 | 0-5 |
| Abrasive grit | n/a | 280 Dry | n/a | (see below) |
| Sanding | n/a | After 24 hours | n/a | After 24 hours |
| Recoat Time 65F./18C | Within 24 hours, no sanding required | Within 24 hours, no sanding required | Within 24 hours, no sanding required | n/a |
| Notes | Can be recoated after 5 hours | |||
When a satin finish is desired:
Sand last coat to 220 grit, apply one or more coats of Epifanes Rubbed Effect Interior Varnish. Sand between coats with 320 grit wet or dry abrasive paper. If desired, replace Rubbed Effect with Epifanes Polyurethane after the fourth coat, sand with 220 grit wet or dry abrasive paper (if topcoating with a one-component product) or 320 wet or dry (if topcoating with a two-component product). Topcoat with three or more coats of Epifanes Clear Gloss Varnish.
More from Epifanes
